I had that problem on my Garmin Vivoactive 3 but my Fenix 6 Pro behaves really well. I get the heart rate readings that I expect from my workouts, trainings and resting HR. My resting HR is normally low like 45-50 which the watch captures well. My cardio is normally between 130 and 150 and the watch is in the range.
\n garmin fenix 6 hr not working

Hi everyone. Until my last two Zwift rides, my heart rate was being picked up without any problem by Zwift (i am running Zwift on my Samsung S20 and am broadcasting my heart rate from my Garmin Fenix 6 wrist watch.) So, at the end of my ride, i was able to see my entire heart rate during the ride on Zwift. My last two rides, however, this is not happening - despite the fact that Zwift shows

Thanks . on 24/7 monitoring/ my watch face . both the watch and Garmin connect. ive also noticed the green light on the back of the watch case has gone off.
Using the Daily Suggested Workout Feature on a Garmin Watch | Garmin Customer Support. FREE GROUND SHIPPING ON ORDERS $25 AND UP. Garmin Support Center. Garmin Support Center is where you will find answers to frequently asked questions and resources to help with all of your Garmin products.
Intensity Minutes not calculating. I’ve only had f6x Pro since Christmas but usually walk 4 times per week and average around 250 intensity minutes per week. This week I have done a few hilly walks (same walks that usually generate data) however only one activity (today) generated data. So far I have 47 minutes complete and that was for today.
Garmin Fenix 6 Pro HR not working anymore. I do have a problem, for the last 3 days i've noticed i've got false reading of sleep data, strees and energy level so i was wondering what changed. It seems the Hr sensor is not working anymore, the lights are turned off and no reading for HR. New Fenix 6 - Heart rate monitor not working properly. rotamonkey 6 months ago. Hi There, Just got this watch and to be honest, for training I haven't been impressed as I generally put it in HIIT mode and do running and weights training but sometimes the heart rate monitor basically just completely dies. It keeps ticking away at some baseline It could also be some sort of interference between wifi and bluetooth. Either way i had no use for wifi sync, so i switched it off. Voila, its all back to normal, syncs up just fine with my phone as it did previously. The other solution is to open it up and replace the battery. That i may well do. Just received my Fenix 6 (in France). But HR sensor doesn't activate itself (or just when watch is switching on, few seconds of green LEDs). But as opposed to other watch (I have the 235), any movement doesn't activate the LEDs. Upgraded 10.10 & Hub 7.11 and checked all parameters (HR auto etc., but it doesn't help.
The running mode and the generic mode seem to work well though. I tried recording my last ski touring outing with the running mode, and then not selecting any sport, and got normal results (140 to 160) both times. It’s as if for hiking and ascension, the software does not sample the HR often enough, or has a setting that screws the HR reading.
Cannot connect HRM Tri / HRM Run. I owned both HRM Tri & Run while checking the connection I noticed that they are just not connected to the watch. I tried to remove my sensors from the list and adding them again .. no luck the watch is not detecting the HRMs (did try with both the HRM Tri & Run). I tested those HRMs with my Garmin Edge
Years ago, Garmin devices just used movement - tracked by motion-sensing accelerometers - and heart rate to analyze your sleep. Since the company debuted 'Advanced Sleep Monitoring', though, heart

2 yr old Fenix, never missed a beat with newest firmware installed. However last night went to bed with 30% battery and woke up to it dead, which has never happened. Charged it up but now he sensor won’t work and it’s sluggish as hell! Like taking 5 to 6 seconds for any button to respond. Tried resetting it multiple times and turning hr on

Heart rate broadcast. I just buy a TACX Neo 2T and want to use my Fenix 6 Sapphire to broadcast the Heart Rate to the app (Zwift or TACX), but: - If I broadcast the HR it stuck at the first value the optical sensor read. - If I use virtual run to broadcast HR it doesn't display the heart rate (only - - is visible on the watch). 3oiq.
  • jz6gftf6er.pages.dev/75
  • jz6gftf6er.pages.dev/573
  • jz6gftf6er.pages.dev/399
  • jz6gftf6er.pages.dev/151
  • jz6gftf6er.pages.dev/377
  • jz6gftf6er.pages.dev/210
  • jz6gftf6er.pages.dev/211
  • jz6gftf6er.pages.dev/136

    • garmin fenix 6 hr not working